FREE
GROUND
SHIPPING
on Parts Orders Over $99.00
Measuring Diagrams
Shop By Vehicle Type
Oldsmobile Pinion Yokes
Denny's Driveshafts offer a variety of Oldsmobile Pinion Yokes. The typical Olds rear end pinion yoke utilizes a strap and bolt design to hold the rear universal joint into the yoke. Disconnecting the 4 bolts and 2 straps is necessary to remove the driveshaft to from the car. Denny's offers both the original equipment strap and bolt design and also the u-bolt design as replacements. Please measure your u-joint width before ordering. The 1310 u-joint will measure 3.219 wide and the 1330 will measure 3.625 wide. Both will have a 1.062 bearing cap diameter.
Please click here for Pinion Yokes
9900047 Pinion Yoke Kit GM 3R Series 27 splines fits Oldsmobile with GM 7.6 inch 10 bolt rear end
$144.95 each
Part Number:
9900047
$144.95 each
9900047
3R Series Pinion Yoke Kit - strap and bolt style
Fits Oldsmobile with GM 7.6 inch 10 Bolt Rear End
27 splines
Fits 3R series u-joint with inside C-Clips
2.556 inches between inside surfaces of yoke
1.128 bearing cap diameter
Includes strap and bolt set
Includes pinion nut and washer
Includes Pinion Seal new style triple lip design
Status: SOLD OUT...More Coming Soon
9900047 Pinion Yoke Kit GM 3R Series 27 splines fits Oldsmobile with GM 7.6 inch 10 bolt rear end
$144.95 each
Part Number:
9900047
$144.95 each
9900047
3R Series Pinion Yoke Kit - strap and bolt style
Fits Chevrolet and GM 7.6 inch 10 Bolt Rear End
27 splines
Fits 3R series u-joint with inside C-Clips
2.556 inches between inside surfaces of yoke
1.128 bearing cap diameter
Includes strap and bolt set
Includes pinion nut and washer
Includes Pinion Seal new style triple lip design
Status: SOLD OUT...More Coming Soon
9984216 Pinion Yoke 30 spline 3R series for inside c-clip u-joint fits Oldsmobile GM 8.5 inch 10 bolt rear end
$59.95 each
Part Number:
9984216
$59.95 each
Part Number 9984216
3R Series Pinion Yoke to replace original equipment
Fits Oldsmobile 8.5 inch 10 Bolt Rear Ends
30 splines
Fits INSIDE "C" Clip style universal joints listed below
Strap and Bolt Style
DIMENSIONS
21A - Height = 3.375 inches
24 - U-Joint lockup Inside dimension = 2.556 inches
22 - U-Joint saddle diameter = 1.125 inches
25 - Seal surface diameter = 1.938
23 - Spline Diameter = 1.312
Status: IN STOCK
9400022 Pinion Yoke KIT 3R series fits 1966 to 1971 Oldsmobile F-85, Cutlass, 4-4-2 with 8.2 inch BOP rear end with 27 spline pinion and bolt in style axles
$138.55 each
Part Number:
9400022
$138.55 each
9400022
3R SERIES PINION YOKE KIT
INCLUDES - pinion nut, washer and u-bolt set
27 spline
U-Bolt style
Fits 1966 to 1971 Oldsmobile F-85, Cutlass, 4-4-2 with BOP rear axle housing with bolt in style axles
Commonly known as the BOP Rear End (Buick-Olds-Pontiac)
1.942 seal surface diameter
DOES NOT FIT early BOP housings that originally had a pinion yoke with the 1.642 seal surface diameter
Status: IN STOCK - FREE SHIPPING
1957-1964 Oldsmobile 1350 Chromoly Pinion Yoke 13 Spline Mark Williams 39018
$208.90 each
Part Number:
MW 39018
$208.90 each
1957-1964 Oldsmobile and Pontiac 1350 series Chromoly 13 Spline Pinion Yoke
Status: FACTORY DIRECT TO YOU
5 Matching Results Found
Results per Page: 2 5