2060989 fits T-400, 4L80, 4L85, 6L80 Transmission Slip yoke for use on Light TRUCK Transmission GM 3R Series 32 spline

Part Number:
2060989

UPC:

Your Cost $160.54

Sorry, sold out

STATUS: DISCONTINUED ITEM

2060989

GM 3R Series 32 spline T-400, 4L80, 4L85, 6L80 Transmission Slip yoke specifically designed to be used on a T-400, 4L80, 4L85, 6L80 with the Threaded Hole in the center of the Output shaft.

DOES NOT FIT.... T400/475 with the emergency brake and or roller bearing in the tailshaft housing as found in the RV Motor Home Transmission and Medium Truck Transmissions
>>>> Please consult a transmission rebuilder to see what is required to convert it to a normal light truck tailshaft and tailshaft housing.

2060989 fits T-400, 4L80, 4L85, 6L80 Transmission Slip yoke for use on Light TRUCK Transmission GM 3R Series 32 spline

Click for Larger Photo

FOR FASTER SERVICE, PLEASE ORDER ALL PARTS ONLINE

STATUS: DISCONTINUED ITEM

YOUR COST: $160.54

2060989

GM 3R Series 32 spline T-400, 4L80, 4L85 and 6L80 Transmission Slip yoke specifically designed to be used on a T-400, 4L80, 4L85, 6L80 with the Threaded Hole in the center of the Output shaft.

This design will replace the truck style bolt on yoke with a car style slip yoke and allow for proper slip travel and bushing contact for best performance.

With this counterbored slip yoke you can now use a normal car style driveshaft.

This slip yoke will slide all the way into the transmission.

We strongly suggest that you remove the O-Ring on the output shaft because with this slip yoke it is no longer necessary.
Removing the O-Ring will to allow the lubrication to get to the splines...and this is very important.

To determine correct driveshaft center to center length for this slip yoke

Push the slip yoke all the way into transmission and pull it out 3/4 inch minimum to 1 inch maximum. Now measure from center of u-joint hole in slip yoke to the center of the u-joint at the rear end yoke. This dimension will be the correct center to center required for your driveshaft to fit correctly using this slip yoke.

We designed this yoke to solve this problem over 30 years ago when T400 Truck Transmissions first started to be used in cars

Barrel Diameter... = 1.886 inches
Fits GM 3R series u-joints
- U-joint cap diameter...= 1-1/8 inches
- U-joint width... = 2.556 inches between the inside surfaces where the "C" clips lock in the u-joint. It wil be 3-5/8 inches cap to cap
Spline count... 32

2060989 fits T-400, 4L80, 4L85, 6L80 Transmission Slip yoke for use on Light TRUCK Transmission GM 3R Series 32 spline

You May Also Need These Parts to Complete the Job

SPICER 5-3147X 3R Series U-joint Greaseable Part#: 5-3147X $19.25	Dana Spicer 5-795X Universal Joint 3R Series Non greaseable Part#: 5-795X $27.95
Neapco 3-3130 Greaseable Combination u-joint to connect 1310 series to 3R Series Part#: 3-3130 $25.95	Dana Spicer 5-3022-1X Combination U-joint to connect Outside Snap Ring 1310 series to Inside "C" Clip GM 3R series Part#: 5-3022-1X $29.95
Dana Spicer 5-793X Combination U-joint 1330 to GM 3R Series Part#: 5-793X $21.98	Dana Spicer 5-212X Universal Joint 1330 to 3R Series Combination U-joint Greaseable Part#: 5-212X $21.80
Neapco 2-1569 Greaseable Combination u-joint to connect 1330 series to 3R Series Part#: 2-1569 ~~$20.73~~ $19.74	Neapco 2-1153 Combination U-joint converts 1350 Series to GM 3R Series GREASEABLE Part#: 2-1153 ~~$39.32~~ $37.45
TIMKEN 9449 REAR Output Seal TH-400, 4L80, 4L85 with 32 Spline output Part#: 9449 $6.46

Enter your email address and we'll send you a message when this item is available

Please enter your email address in order to be notified when this item is available.

[ X ]

Chevrolet > CAMARO 1967 to 2002 > Transmission Slip Yokes > 32 Spline Automatic or Manual > INSIDE CLIPS

You May Also Need These Parts to Complete the Job

Enter your email address and we'll send you a message when this item is available