Product Search

Denny's Driveshaft builds custom steel and aluminum driveshafts for your high performance car, street rod, race car, van, pick up or 4x4 truck

FREE
GROUND
SHIPPING on Parts Orders
Over $99.00

Measuring Diagrams

How to Measure Correctly

Driveshafts

1350 Nitrous Ready Driveshafts Street Rod Driveshafts Street Rod HD Driveshafts Aluminum 6061-T6 Driveshafts Cobra Kit Car Driveshafts 4x4 TRUCK Driveshafts 2WD TRUCK Driveshafts

Shop By Vehicle Type

CHEVROLET - Parts BUICK - Parts PONTIAC - Parts OLDSMOBILE - Parts DODGE - MOPAR Parts JEEP - Parts FORD - Parts LINCOLN - Parts

Driveline Parts

• AXLE DIFF - 4X4 FRONT DIFF PARTS • AXLE DIFF - REAR END PARTS • AXLE SHAFTS REAR DIFF • BALL JOINTS / KING PIN PARTS • BEARINGS - DIFFERENTIAL KITS • BEARINGS - Driveshaft Center Support • BEARINGS - Sets - Cups - Cones - Needle • BUILD IT YOURSELF - PARTS LISTS • BUSHINGS TO ADAPT TUBE SIZE • COMPANION FLANGES • CRUSH SLEEVE - Collapsable Spacer • CV BALL STUD YOKES Double Cardan • CV PARTS - Double Cardan Driveshaft • DIFF COVERS, BOLTS, GASKETS • DIFFERENTIAL PARTS - FRONT / REAR • DIFFERENTIAL PARTS - POSITRACTION • DUST CAPS - SEALS - RUBBER BOOTS • FLANGE YOKES • GEARS - Ring and Pinion • GIFT CERTIFICATES • HARDWARE - U-Bolts, Straps, Nuts more • INFO LIBRARY • LUBRICANTS - Grease • PARTS - AAM Driveshaft and Axle • PARTS - ALL Driveshaft and Driveline • PARTS - NEAPCO by Part Number • PARTS - NEW ARRIVALS • PARTS - YUKON • PINION NUTS and WASHERS • PINION YOKES FRONT or REAR END • PTO PARTS Power Take Off and AG • RING GEAR BOLTS • SEALS - Oil and Grease • SHIMS, BAFFLES, SLINGERS • SLIP YOKES - AAM ONLY • SLIP YOKES - CHROMOLY • SLIP YOKES - DANA SPICER ONLY • SLIP YOKES - DOUBLE CARDAN CV • SLIP YOKES - Driveshaft Spline/Slip • SLIP YOKES - T400, 4L80 TRUCK TRANS • SLIP YOKES - TRANSFER CASE • SLIP YOKES - TRANSMISSION Auto/Man • SPINDLE NUTS, WASHERS, STUDS • SPINDLES 4x4 FRONT • SPLINE / SLIP YOKE MATCHED SETS • SPLINES - Center Brg Bolt On Yoke Style • SPLINES - Center Brg Slip Yoke Style • SPLINES - DANA SPICER ONLY • SPLINES - Use with Slip Yoke • TRANSFER CASE END YOKE - BOLT ON • TRANSMISSION END YOKE - BOLT ON • TUBING - ALUMINUM DRIVESHAFT • TUBING - STEEL DRIVESHAFT • UNIVERSAL JOINTS - 4X4 AXLE • UNIVERSAL JOINTS - Car and Light Truck • UNIVERSAL JOINTS - CONVERSION • UNIVERSAL JOINTS - HD TRUCK and EQUIP • WELD YOKES - ALUMINUM • WELD YOKES - STEEL

Product Search

Free Shipping on Parts Orders Over $99.00

Customer Testimonials

Thank you Denny, you are a breath of fresh air in the auto, parts and service, you know your business and care about your customer service you helped me when other outfits couldn't Thanks Again! SM
...read more

Sebastian M ~ Newalla , OK

Click here to send us your testimonial

Aftermarket Driveshaft 1.378 Bearing

X-1378 Center Support with 1.378 bearing ID Aluminum Urethane Mount for 1958 to 1964 Chevy Car and 1960 to 1972 C-10 Truck for use with custom aftermarket driveshaft

Part Number:
X-1378

UPC:

Your Cost $210.95

Sorry, sold out

CLICK HERE to be NOTIFIED when this item is available

STATUS: SOLD OUT...More Coming Soon

Denny's part number X-1378

Aluminum Urethane mounted center support bearing

WILL NOT FIT STOCK DRIVESHAFT

Can be used on 2.5 inch or 3 inch diameter custom built 2 piece driveshafts that require a 1.378 ID bearing

Ideal for building larger and stronger two piece driveshaft in 1310 or 1350 series
Bearing ID is 1.378 for use with custom built aftermarket driveshaft
Must be used with spline and slip style rear driveshaft section
Aluminum Mounting fits Chevrolet Car frame
- 1958, 1959, 1960, 1961, 1962, 1963, 1964
Aluminum Mounting fits Chevy C-10 1/2 Ton Truck frame
- 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968, 1969, 1970, 1971, 1972

Super Strong aircraft aluminum housing will not bend or twist.

Bearing is suspended in Urethane and will not pull out under load like the original rubber mount did when it distorted under load.
This could be the cure that you have been looking for to end all your problems with center hanger bearing failure
Great for cars and trucks with hydraulic suspensions
Comes with Mounting Bolts and washers

Denny's part number X-1378 Center Support Bearing Aluminum Urethane Mount for 1958 to 1964 Chevy Car and 1960 to 1972 C-10 Truck

Click for Larger Photo

FOR FASTER SERVICE, PLEASE ORDER ALL PARTS ONLINE

STATUS: SOLD OUT...More Coming Soon

YOUR COST: $210.95

Denny's part number X-1378

Aluminum Urethane mounted center support bearing

WILL NOT FIT STOCK DRIVESHAFT

Can be used on 2.5 inch or 3 inch diameter custom built 2 piece driveshafts that require a 1.378 ID bearing

Ideal for building larger and stronger two piece driveshaft in 1310 or 1350 series
Bearing ID is 1.378 for use with custom built aftermarket driveshaft
Must be used with spline and slip style rear driveshaft section
Aluminum Mounting fits Chevrolet Car frame
- 1958, 1959, 1960, 1961, 1962, 1963, 1964
Aluminum Mounting fits Chevy C-10 1/2 Ton Truck frame
- 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967, 1968, 1969, 1970, 1971, 1972

Super Strong aircraft aluminum housing will not bend or twist.

Bearing is suspended in Urethane and will not pull out under load like the original rubber mount did when it distorted under load.
This could be the cure that you have been looking for to end all your problems with center hanger bearing failure
Great for cars and trucks with hydraulic suspensions
Comes with Mounting Bolts and washers

Denny's part number X-1378 Center Support Bearing Aluminum Urethane Mount for 1958 to 1964 Chevy Car and 1960 to 1972 C-10 Truck

Enter your email address and we'll send you a message when this item is available

Please enter your email address in order to be notified when this item is available.

[ X ]