9995588 Pinion Yoke 1410 Series Forged U-Bolt style fits 1985 to 1992 FORD F250, F350 Super Duty with 10.25 inch Sterling rear end

Part Number:
9995588

UPC:

Your Cost $159.95

STATUS: IN STOCK - FREE SHIPPING

9995588

Pinion Yoke for FORD Super Duty Rear End
- Fits Ford F250, F350 Super Duty Truck with 10.25 inch FORD Sterling Rear
  - 1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992

31 Splines 1.343 spline diameter
U- Bolt style
FORGED Steel for extra strength
Comes with pinion nut and u-bolt set
1410 Series - fits 1410 series universal joint 5-160X or 5-1410X ... see bottom of this page
- E = Fits Universal joint 4.188 inches (4-3/16) wide cap to cap
- D = Fits u-joint bearing cap diameter 1.188 inch (1-3/16)
- Q = 1.265 inches through splined hole
- S = 3.150 inches tall
- R = 1.812 inches seal surface diameter

THIS Yoke is approximately 3-1/8 inches TALL

IMPORTANT: Late 1992 and newer 1993, 1994, 1995, 1996, 1997, 1998 Ford 10.25 inch Sterling rear end pinion yokes could be 3.5 inches (3-1/2) tall. Please check yours to be sure before ordering.

CLICK HERE if you need the 3-1/2 inch tall 1410 pinion yoke part number 9929901 for 10.25 inch from 1993 to 1998

NOTES:

DOES NOT fit Ford Super duty with DANA rear end
NOT compatible with 1330 series driveshaft.
NOT compatible with 1350 series driveshaft
- CLICK HERE for 1350 Ford Sterling pinion yokes

9995588 Pinion Yoke 1410 Series Forged U-Bolt style fits 1985 to 1992 FORD F250, F350 Super Duty with 10.25 inch Sterling rear end

Click for Larger Photo

FOR FASTER SERVICE, PLEASE ORDER ALL PARTS ONLINE

STATUS: IN STOCK - FREE SHIPPING

YOUR COST: $159.95

9995588

Pinion Yoke for FORD Super Duty Rear End
- Fits Ford F250, F350 Super Duty Truck with 10.25 inch FORD Sterling Rear
  - 1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992

31 Splines 1.343 spline diameter
U- Bolt style
FORGED Steel for extra strength
Comes with pinion nut and u-bolt set
1410 Series - fits 1410 series universal joint 5-160X or 5-1410X ... see bottom of this page
- E = Fits Universal joint 4.188 inches (4-3/16) wide cap to cap
- D = Fits u-joint bearing cap diameter 1.188 inch (1-3/16)
- Q = 1.265 inches through splined hole
- S = 3.150 inches tall
- R = 1.812 inches seal surface diameter

THIS Yoke is approximately 3-1/8 inches TALL

CLICK HERE if you need the 3-1/2 inch tall 1410 pinion yoke part number 9929901 for 10.25 inch from 1993 to 1998

NOTES:

DOES NOT fit Ford Super duty with DANA rear end
NOT compatible with 1330 series driveshaft.
NOT compatible with 1350 series driveshaft
- CLICK HERE for 1350 Ford Sterling pinion yokes

9995588 Pinion Yoke 1410 Series Forged U-Bolt style fits 1985 to 1992 FORD F250, F350 Super Duty with 10.25 inch Sterling rear end

You May Also Need These Parts to Complete the Job

Dana Spicer 5-160X Universal Joint 1410 Series Part#: 5-160X $24.95	Dana Spicer 5-1410X Universal Joint 1410 Series NON Greaseable Part#: 5-1410X $31.95
TIMKEN 4278 Rear End Pinion Seal fits Ford Excursion, Expedition, F250, F350 Super Duty, E Series VANS with 10.25 and 10.5 inch rear ends Part#: 4278 $14.42

Enter your email address and we'll send you a message when this item is available

Please enter your email address in order to be notified when this item is available.

[ X ]

Driveshaft and Driveline Parts > PINION YOKES - Front and Rear End > Ford 10.25 and 10.50 STERLING > 1410 Series - 4.188 X 1.188

You May Also Need These Parts to Complete the Job

Enter your email address and we'll send you a message when this item is available