Product Search

Denny's Driveshaft builds custom steel and aluminum driveshafts for your high performance car, street rod, race car, van, pick up or 4x4 truck

FREE
GROUND
SHIPPING on Parts Orders
Over $99.00

Measuring Diagrams

How to Measure Correctly

Driveshafts

1350 Nitrous Ready Driveshafts Street Rod Driveshafts Street Rod HD Driveshafts Aluminum 6061-T6 Driveshafts Cobra Kit Car Driveshafts 4x4 TRUCK Driveshafts 2WD TRUCK Driveshafts

Shop By Vehicle Type

CHEVROLET - Parts BUICK - Parts PONTIAC - Parts OLDSMOBILE - Parts DODGE - MOPAR Parts JEEP - Parts FORD - Parts LINCOLN - Parts

Driveline Parts

• AXLE DIFF - 4X4 FRONT DIFF PARTS • AXLE DIFF - REAR END PARTS • AXLE SHAFTS REAR DIFF • BALL JOINTS / KING PIN PARTS • BEARINGS - DIFFERENTIAL KITS • BEARINGS - Driveshaft Center Support • BEARINGS - Sets - Cups - Cones - Needle • BUILD IT YOURSELF - PARTS LISTS • BUSHINGS TO ADAPT TUBE SIZE • COMPANION FLANGES • CRUSH SLEEVE - Collapsable Spacer • CV BALL STUD YOKES Double Cardan • CV PARTS - Double Cardan Driveshaft • DIFF COVERS, BOLTS, GASKETS • DIFFERENTIAL PARTS - FRONT / REAR • DIFFERENTIAL PARTS - POSITRACTION • DUST CAPS - SEALS - RUBBER BOOTS • FLANGE YOKES • GEARS - Ring and Pinion • GIFT CERTIFICATES • HARDWARE - U-Bolts, Straps, Nuts more • INFO LIBRARY • LUBRICANTS - Grease • PARTS - AAM Driveshaft and Axle • PARTS - ALL Driveshaft and Driveline • PARTS - NEAPCO by Part Number • PARTS - NEW ARRIVALS • PARTS - YUKON • PINION NUTS and WASHERS • PINION YOKES FRONT or REAR END • PTO PARTS Power Take Off and AG • RING GEAR BOLTS • SEALS - Oil and Grease • SHIMS, BAFFLES, SLINGERS • SLIP YOKES - AAM ONLY • SLIP YOKES - CHROMOLY • SLIP YOKES - DANA SPICER ONLY • SLIP YOKES - DOUBLE CARDAN CV • SLIP YOKES - Driveshaft Spline/Slip • SLIP YOKES - T400, 4L80 TRUCK TRANS • SLIP YOKES - TRANSFER CASE • SLIP YOKES - TRANSMISSION Auto/Man • SPINDLE NUTS, WASHERS, STUDS • SPINDLES 4x4 FRONT • SPLINE / SLIP YOKE MATCHED SETS • SPLINES - Center Brg Bolt On Yoke Style • SPLINES - Center Brg Slip Yoke Style • SPLINES - DANA SPICER ONLY • SPLINES - Use with Slip Yoke • TRANSFER CASE END YOKE - BOLT ON • TRANSMISSION END YOKE - BOLT ON • TUBING - ALUMINUM DRIVESHAFT • TUBING - STEEL DRIVESHAFT • UNIVERSAL JOINTS - 4X4 AXLE • UNIVERSAL JOINTS - Car and Light Truck • UNIVERSAL JOINTS - CONVERSION • UNIVERSAL JOINTS - HD TRUCK and EQUIP • WELD YOKES - ALUMINUM • WELD YOKES - STEEL

Product Search

Free Shipping on Parts Orders Over $99.00

Customer Testimonials

Just a note to thank you guys for the super job you did for me. The shaft is as smooth as any I have ever run. The car has picked up about 8 hundreds. You are very professional and patient while getting all the facts over the phone. Thanks again, ...
...read more

Clyde W ~ Lexington , KY

Click here to send us your testimonial

SPLINE and SLIP

Dana Spicer 3-3-508KX Slip Yoke 1410 series 16 spline 7.812 inches

Part Number:
3-3-508KX

UPC:

023913228828

Your Cost $81.95

STATUS: IN STOCK

DANA SPICER 3-3-508KX

1410 series Slip Yoke

Fits Spline and Slip Style Driveshaft

It will fit in place of the original slip yoke on any 16 spline driveshaft with a spline diameter of 1.5 inches
16 splines and 1.5 inch Spline Diameter
7.812 inches from center of u-joint bearing cap to end of yoke with seal removed.

SAME AS - ALTERNATE

Neapco N3-3-508KX

Dana Spicer 3-3-508KX Slip Yoke 1410 series 16 spline 7.812 inches

Click for Larger Photo

FOR FASTER SERVICE, PLEASE ORDER ALL PARTS ONLINE

STATUS: IN STOCK

YOUR COST: $81.95

DANA SPICER 3-3-508KX

1410 series Slip Yoke

Fits Spline and Slip Style Driveshaft

It will fit in place of the original slip yoke on any 16 spline driveshaft with a spline diameter of 1.5 inches

Designed for 1410 series u-joint. See bottom of this page for 1410 series u-joints

4 3/16 inches between snap rings
1 3/16 diameter bearing caps

16 splines and 1.5 inch Spline Diameter

Fits 16 spline driveshaft with 1.5 spline Diameter
- For proper fit be sure to Measure OUTSIDE DIAMETER of SPLINED SHAFT
Includes SCREW on seal
7.812 inches from center of u-joint bearing cap to end of yoke with seal removed.
- Measure from CENTER of Bearing Cap Hole to END of Yoke with seal removed