Product Search

Denny's Driveshaft builds custom steel and aluminum driveshafts for your high performance car, street rod, race car, van, pick up or 4x4 truck

FREE
GROUND
SHIPPING on Parts Orders
Over $99.00

Measuring Diagrams

How to Measure Correctly

Driveshafts

1350 Nitrous Ready Driveshafts Street Rod Driveshafts Street Rod HD Driveshafts Aluminum 6061-T6 Driveshafts Cobra Kit Car Driveshafts 4x4 TRUCK Driveshafts 2WD TRUCK Driveshafts

Shop By Vehicle Type

CHEVROLET - Parts BUICK - Parts PONTIAC - Parts OLDSMOBILE - Parts DODGE - MOPAR Parts JEEP - Parts FORD - Parts LINCOLN - Parts

Driveline Parts

• AXLE DIFF - 4X4 FRONT DIFF PARTS • AXLE DIFF - REAR END PARTS • AXLE SHAFTS REAR DIFF • BALL JOINTS / KING PIN PARTS • BEARINGS - DIFFERENTIAL KITS • BEARINGS - Driveshaft Center Support • BEARINGS - Sets - Cups - Cones - Needle • BUILD IT YOURSELF - PARTS LISTS • BUSHINGS TO ADAPT TUBE SIZE • COMPANION FLANGES • CRUSH SLEEVE - Collapsable Spacer • CV BALL STUD YOKES Double Cardan • CV PARTS - Double Cardan Driveshaft • DIFF COVERS, BOLTS, GASKETS • DIFFERENTIAL PARTS - FRONT / REAR • DIFFERENTIAL PARTS - POSITRACTION • DUST CAPS - SEALS - RUBBER BOOTS • FLANGE YOKES • GEARS - Ring and Pinion • GIFT CERTIFICATES • HARDWARE - U-Bolts, Straps, Nuts more • INFO LIBRARY • LUBRICANTS - Grease • PARTS - AAM Driveshaft and Axle • PARTS - ALL Driveshaft and Driveline • PARTS - NEAPCO by Part Number • PARTS - NEW ARRIVALS • PARTS - YUKON • PINION NUTS and WASHERS • PINION YOKES FRONT or REAR END • PTO PARTS Power Take Off and AG • RING GEAR BOLTS • SEALS - Oil and Grease • SHIMS, BAFFLES, SLINGERS • SLIP YOKES - AAM ONLY • SLIP YOKES - CHROMOLY • SLIP YOKES - DANA SPICER ONLY • SLIP YOKES - DOUBLE CARDAN CV • SLIP YOKES - Driveshaft Spline/Slip • SLIP YOKES - T400, 4L80 TRUCK TRANS • SLIP YOKES - TRANSFER CASE • SLIP YOKES - TRANSMISSION Auto/Man • SPINDLE NUTS, WASHERS, STUDS • SPINDLES 4x4 FRONT • SPLINE / SLIP YOKE MATCHED SETS • SPLINES - Center Brg Bolt On Yoke Style • SPLINES - Center Brg Slip Yoke Style • SPLINES - DANA SPICER ONLY • SPLINES - Use with Slip Yoke • TRANSFER CASE END YOKE - BOLT ON • TRANSMISSION END YOKE - BOLT ON • TUBING - ALUMINUM DRIVESHAFT • TUBING - STEEL DRIVESHAFT • UNIVERSAL JOINTS - 4X4 AXLE • UNIVERSAL JOINTS - Car and Light Truck • UNIVERSAL JOINTS - CONVERSION • UNIVERSAL JOINTS - HD TRUCK and EQUIP • WELD YOKES - ALUMINUM • WELD YOKES - STEEL

Product Search

Free Shipping on Parts Orders Over $99.00

Customer Testimonials

It was about 8 months after I received their driveline before I actually installed it, but I remember how specific they were about all my measurements be fore ordering it, and when I finally removed my driveline it looked to be a little loner than mine...
...read more

Robert W ~ Baker City , OR

Click here to send us your testimonial

TRANSFER CASE... Bolt On Yokes

Neapco N2-4-5341 CV YOKE 1310 Series 32 Spline for NP 203 205 208 241 Transfer CaseCV Yoke NP203 205 208 Transfer Case 1310 Series 32 Spline

Part Number:
N2-4-5341

UPC:

083869002682

Your Cost $83.95

STATUS: IN STOCK

NEAPCO N2-4-5341

1310 Series NP203 NP205 NP208 Transfer Case 32 spline CV style yoke

Neapco N2-4-5341 CV YOKE 1310 Series 32 Spline for NP 203 205 208 241 Transfer CaseCV Yoke NP203 205 208 Transfer Case 1310 Series 32 Spline

Click for Larger Photo

FOR FASTER SERVICE, PLEASE ORDER ALL PARTS ONLINE

STATUS: IN STOCK

YOUR COST: $83.95

NEAPCO N2-4-5341

1310 Series NP203 NP205 NP208 Transfer Case 32 spline CV style yoke

Use this 1310 series CV Yoke to replace your original equipment NON CV yoke when installing a 1310 Series CV Driveshaft onto any fixed yoke style New Process Transfer Case with a 32 spline output

32 spline
1.875 seal diameter
- This yoke will require a new rear output seal. Please see the bottom of this page for our CV Yoke Replacement Seals
1310 Series is 3 7/32 between tabs with 1.062 bearing cap diameter
Requires 1 1/8 inch Socket Head Nut. See listing at bottom of page.
- This yoke may require the purchase of a new nut to replace original. To be sure if you will need the new nut please check your original nut and if you need a socket larger than 1 1/8 inch to remove your original nut then you will need the new nut. Please see the bottom of this page for CV Yoke Replacement Nut.
Requires 4 CV Bolts to connect 1310 CV Driveshaft to this yoke. See listing at bottom of page
SPLINE OD = 1.401
D = 1.062
E = 3.219
Q = 2.000
R = 1.875
S = 3.875

Neapco N2-4-5341 CV YOKE 1310 Series 32 Spline for NP 203 205 208 241 Transfer CaseCV Yoke NP203 205 208 Transfer Case 1310 Series 32 Spline

You May Also Need These Parts to Complete the Job

CV Yoke Bolts .312 x 24 Fine Thread fits Dana Spicer 211355X, 211544X, 211179X, 211996X and Neapco N3-83-019 centering yokes Part#: 4289-516 $2.95	Dana Spicer NUT for REAR OUTPUT Yoke fits 32 spline New Process 203, 205, 208 and 241 Transfer Case CV Yoke Part#: 44189 $2.95
S1875-1 Rear output seal for CV Yoke 2.750 OD with 1.875 ID for 1973-1979 NP 203 Part#: S1875-1 $14.95	S1875-2 Rear output seal use with CV Yoke 3.066 OD with 1.875 ID for 1971-1979 NP 205 Part#: S1875-2 $13.95

Enter your email address and we'll send you a message when this item is available

Please enter your email address in order to be notified when this item is available.

[ X ]

You May Also Need These Parts to Complete the Job

CV Yoke Bolts .312 x 24 Fine Thread fits Dana Spicer 211355X, 211544X, 211179X, 211996X and Neapco N3-83-019 centering yokes

$2.95

Dana Spicer NUT for REAR OUTPUT Yoke fits 32 spline New Process 203, 205, 208 and 241 Transfer Case CV Yoke

$2.95

S1875-1 Rear output seal for CV Yoke 2.750 OD with 1.875 ID for 1973-1979 NP 203

$14.95

S1875-2 Rear output seal use with CV Yoke 3.066 OD with 1.875 ID for 1971-1979 NP 205

$13.95